Category Archives: Driveline

Multidrive MDT Tru Tracker

Today we are checking out the Multi Drive Technology Tru Tracker which is a “Rear Track Correction System” for the V8 70 Series Toyota Landcruiser four wheel drive vehicle.

Design Objectives & History

In 2007 Toyota introduced the V8 diesel engine into its 70 Series model range in Australia.

To accommodate the larger engine, the engine bay was widened and front track width was increased, while the rear remained unchanged.

The result is an OEM track width difference of 95mm.

The narrower track at the rear causes the vehicle to sway unpredictably when travelling on soft surfaces.

This also occurs when the vehicle encounters dry wheel ruts or edged surface changes on sealed roads.

Instability issues are also present when towing or with heavily loaded vehicles with a high centre of gravity.

This presents as a significant safety concern as the vehicle can become unstable and difficult to control under these conditions.

The solution is to fit the MDT Tru Tracker which is a complete rear track width correction system.

The components relocate the entire wheel hub assembly to the correct location and equalise the track widths.

As opposed to illegall offset rims or wheel spacers, the Tru Tracker is fully engineered and ADR compliant.

Video

Overview

Features & Benefits

  • Improved dynamic stability and handling on sealed and well-formed roads
  • Significantly improved tracking, driver control and handling in loose / deformable soils such as mud, gravel or sand
  • Improved stability when towing
  • Improved responsiveness
  • Improved rollover resistance
  • Complete Rear Axle Width Correction
  • Improved Off-Road Safety
  • Increased Fuel Economy
  • Utilises existing Diff Housing

Installation

Easy to install… the Tru Tracker finally allows you to enjoy the benefits of putting the rear wheels where they should be!

Installation is super easy and completed on the vehicle with minimal modifications required utilising many of the existing OEM components.

How to install?


Download Installation Instructions

Gallery

Multidrive Technology MDT Tru Tracker Kit
Multidrive Technology MDT Tru Tracker Kit
Closeup view of the wheel stud shaft end of the extended rear axle
Closeup view of the wheel stud shaft end of the extended rear axle
Complete view of the Tru Tracker extended rear axle
Complete view of the Tru Tracker extended rear axle
Complete view of the Tru Tracker short brake line
Complete view of the Tru Tracker short brake line
Closeup view of the spline on the Tru Tracker extended rear axle
Closeup view of the spline on the Tru Tracker extended rear axle
Closeup side view of the extended stub on the Tru Tracker rear axle
Closeup side view of the extended stub on the Tru Tracker rear axle
Closeup front on view of the extended stub on the Tru Tracker rear axle
Closeup front on view of the extended stub on the Tru Tracker rear axle
Rear view of a 79 Series Landcruiser fitted with a Multidrive Technology MDT Tru Tracker rear axle kit
Rear view of a 79 Series Landcruiser fitted with a Multidrive Technology MDT Tru Tracker rear axle kit
Closeup view of a fitted Multidrive Technology MDT Tru Tracker rear axle on a 79 Series Toyota Landcruiser
Closeup view of a fitted Multidrive Technology MDT Tru Tracker rear axle on a 79 Series Toyota Landcruiser
Right side view of a grey 79 Series Toyota Landcruiser fitted with a Multidrive Technology MDT Tru Tracker rear axle kit
Right side view of a grey 79 Series Toyota Landcruiser fitted with a Multidrive Technology MDT Tru Tracker rear axle kit

Summary

All components are manufactured from high grade materials and thoroughly tested to ensure the strength and reliability of the rear axle assembly is retained.

Each component has undergone Finite Element Analysis (FEA) and has full Engineering Approval.

Toyota warranty is matched on all Tru Tracker components, with the system being available for fitment at the Superior Engineering workshop.

The result of fitting the Tru Tracker system is improved dynamic stability and handling on sealed and well-formed roads.

Significantly improved tracking, driver control and handling in loose and deformable soils such as mud, gravel or sand.

Improved stability when towing, improved responsiveness and improved rollover resistance.

The safety improvement is dramatic and will give any Landcruiser owner a renewed sense of confidence in their vehicle.


For More Information Click Here

Diff Drop Kit Holden Colorado & Isuzu D-Max

This is a Superior Engineering Heavy Duty Diff Drop Kit to suit the Holden Colorado RG and Isuzu D-Max (2012 On) four wheel drive vehicles.

Video

Announcement:

It has been advised by the Superior Engineering Research & Development team that this diff drop kit also fits the Isuzu M-UX.

Design Objectives

The problem with Independent Front Suspension vehicles after fitting a suspension lift is the mis-alignment of the front diff and suspension geometry.

This limitation with IFS design is the major cause of vibrations, steering problems and premature wear and damage to the vehicles cv joints and cv boots.

The Three Main advantages of Superior’s newly designed diff drop bracket are:

  1. They are designed to drop the front differential 30mm lower to re-align and fix the cv angle after a lift has been fitted.
  2. They are also designed to replace your factory crossmember with something much stronger which can withstand harsh punishment and rigors of driving offroad.
  3. Designed for maximum coverange to protect the sump without compromising the performance of your 4wd.

That’s a whole lot of bang for your buck.

Features & Benefits

The bracket is CAD engineered for the ultimate in durability and strength, laser cut from tough heavy duty 350 grade high quality Australian steel, CNC pressed for a precise fit, then sand-blasted and powder coated for hard wearing corrosion resistant protective finsh.

Drain holes are also included for easy care and maintenance, it utilises factory mounts for a straignt up fit, and is fabricated by trained qualified professionals.

This diff drop kit is proudly manufactured right here in Australia by Superior Engineering.

This ensures your getting a true quality GENUINE component, unlike the slightly cheaper and greatly weaker Chinese versions starting to appear within the industry.

A full fitting kit is provided, which includes all the necessary high tensile bolts, spacers, washers and instructions for a quick, easy, straight-up installation.

To top it all off, they are 100% Street Legal and Compliant, and DO NOT require separate approvals to be used on Public roads within Australia and its territories.

This Superior diff drop kit is the best investment you can make to extend the life of your cv joints and suspension components.

Upgrade now to a Superior Engineering Diff Drop Kit and take home ‘Piece of Mind’ that you’re prolonging the life of your IFS suspension system and that your 4×4 vehicle is fitted with a heavy duty structural crossmember.


Want More Information

Technical Features & Highlights

  • 30mm drop to fix CV angles
  • Heavy duty structural aftermarket component
  • Made from Australian 350 premium grade steel
  • Features a simple design for super easy care and maintenance
  • Utilises factory mounts for added strength and straight up fitting
  • Made in Australia at the Brisbane warehouse and workshop
  • Corrosion resistant finish for an extra long life
  • Manufactured by Superior’s highly trained qualified fabricators
  • Sand-blasted and powder-coated
  • Precision machined cut spacers
  • Laser cut for a precise fit

Installation

The kit comes ‘Ready to Fit’ straight out of the box.

Includes all grade 8 hardware, for a direct 100% bolt-in installation with NO cutting, drilling or welding needed.

Includes the following components:

  • 1 x Diff Drop Crossmember
  • 2 x Diff Drop Bosses
  • 3 x M14 x 1.5 x 120mm Bolt
  • 2 x M14 Flat Washer
  • 2 x M14 Spring Washer
  • 1 x M14 x 1.5 Nylock / Conelock Nut

Gallery

Underside view of the Superior 30mm Diff Drop Kit fitted to a Holden Colorado
Underside view of the Superior 30mm Diff Drop Kit fitted to a Holden Colorado

Installing the Superior 30mm Diff Drop Kit onto a Holden Colorado
Installing the Superior 30mm Diff Drop Kit onto a Holden Colorado

Close up view of the Superior Engineering Diff Drop Kit fitted onto a RG Colorado
Close up view of the Superior Engineering Diff Drop Kit fitted onto a RG Colorado

A pack of the complete bolts, nuts, washers and spacers that come with the diff drop kit
A pack of the complete bolts, nuts, washers and spacers that come with the diff drop kit

Laser cut and cnc pressed Diff Drop bracket on display at the Superior 4WD showroom
Laser cut and cnc pressed Diff Drop bracket on display at the Superior 4WD showroom

Closeup view of the heavy duty fabricated Diff Drop bracket on display at the Superior 4WD showroom
Closeup view of the heavy duty fabricated Diff Drop bracket on display at the Superior 4WD showroom

Closeup view of the heavy duty Diff Drop bracket factory mounting points
Closeup view of the heavy duty Diff Drop bracket factory mounting points

Front angle view of the heavy duty Diff Drop bracket on display at the Superior Engineering 4x4 shop
Front angle view of the heavy duty Diff Drop bracket on display at the Superior Engineering 4×4 shop

The Diff Drop bracket comes ready to fit with the bracket, hardware and easy to follow install instructions
The Diff Drop bracket comes ready to fit with the bracket, hardware and easy to follow install instructions

Summary

Just to recap, the Superior Engineering diff drop is Australian made and manufactured from heavy duty 350 grade steel, then CNC machined for the ultimate in durability and performance.

This underbody component is sand blasted and black powder coated for maximum durability and the highest quality finish.

They are custom designed to suit the RG Holden Colorado and 2012 to current Isuzu D-Max four wheel drive vehicles.

So, if you want to protect your vehicle CV joints and suspension geometry then you need a Superior Engineering structural diff drop kit.

They are available to purchase on the Superior website, over the phone during business hours or in-person at the Superior Engineering Deception Bay 4×4 Super Showroom.


Want More Information Click Here or Comment Below

Crossmember With Diff Drop Toyota Landcruiser 100 Series

This is a Superior Engineering Heavy Duty Cross Member with a 20mm Diff Drop to suit the Toyota Landcruiser 100 Series (IFS Front) four wheel drive vehicle.

Video

Design Objectives

The problem with Independent Front Suspension (IFS) vehicles after fitting a suspension lift is the mis-alignment of the front diff and suspension geometry.

This limitation with IFS design is the major cause of vibrations, steering problems and premature wear and damage to the vehicles cv joints and cv boots.

The Two Main advantages of the Superior newly designed crossmember bracket are:

  1. They are designed to replace your OE / factory crossmember with something much stronger which can withstand harsh punishment and rigors of driving offroad.
  2. They are also designed to correct the geometry on the front driveshaft and drop the front differential 20mm lower to re-align and fix the cv angle after a lift has been fitted.

That’s a whole lot of bang for your buck.

Advancements

The crossmember is CAD engineered for the ultimate in durability and strength, laser cut from tough heavy duty 350 grade high quality Australian steel, CNC pressed for a precise fit, then sand-blasted and powder coated for hard wearing corrosion resistant protective finish.

Small drain holes are also included for easy drainage, the member utilises factory mounts for a straight up fit, and fabricated by trained qualified professionals.

This Crossmember is proudly manufactured right here in Australia by Superior Engineering ensuring you get a true quality GENUINE component, unlike the slightly cheaper and greatly weaker Chinese versions starting to appear in the marketplace.

A full fitting kit is provided, which includes all the necessary high tensile bolts, spacers, washers and instructions for a quick, easy, installation.

To top it all off, they are 100% Street Legal and Compliant, and DO NOT require separate approvals to be used on Public roads within Australia and it’s territories.

This Superior CrossMember and diff drop kit is the best investment you can make to extend the life of your cv joints and suspension components.

Upgrade now to a Superior Engineering CrossMember with Diff Drop and take home ‘Piece of Mind’ that you’re prolonging the life of your IFS suspension system and that your 4×4 vehicle is fitted with a properly designed structural crossmember.


Want More Information

Technical Features

  • 20mm drop to fix CV angles
  • Heavy duty structural aftermarket component
  • Made from premium Australian 350 grade 4mm steel
  • Features a simple design for easy care and maintenance
  • Utilises factory mounts for added strength
  • Fabricated by trained qualified professionals
  • Made in Australia at the Brisbane warehouse and workshop
  • Corrosion resistant finish for a long life
  • Manufactured by Superior’s highly trained qualified professional fabricators
  • Sand blasted and powder coated
  • Precision machined cut spacers
  • Laser cut for a precise fit

Installation

The kit comes ‘Ready to Fit’ straight out of the box.

Includes all grade 8 hardware, for a direct 100% bolt-in installation with NO cutting, drilling or welding needed.

Includes the following components:

  • 1 x Crossmember
  • 2 x 40mm x 20mm Steel Boss
  • 6 x 30mm x 20mm Steel Boss
  • 6 x M8 1.25 x 40mm Bolts
  • 6 x M8 Spring Washers
  • 6 x M8 Flat Washers
  • 1 x M14 x 130mm Bolt
  • 1 x M14 Flat Washer

Gallery

A Superior crossmember on the display wall at the retail showroom
A Superior crossmember on the display wall at the retail showroom

Front view of a heavy duty Superior crossmember on the display at the 4x4 retail showroom
Front view of a heavy duty Superior crossmember on the display at the 4×4 retail showroom

Closeup view of the heavy duty Superior crossmember with diff drop showing the mounting points
Closeup view of the heavy duty Superior crossmember with diff drop showing the mounting points

Closeup view of the heavy duty fabrication, welding, cnc folding and black powder coat finish
Closeup view of the heavy duty fabrication, welding, cnc folding and black powder coat finish

Rear view of a Superior crossmember with diff drop showing the quality fabrication and laser cut precision
Rear view of a Superior crossmember with diff drop showing the quality fabrication and laser cut precision

A complete set of grade 8 hardware to fit the Superior crossmember with diff drop kit
A complete set of grade 8 hardware to fit the Superior crossmember with diff drop kit

A completed Superior crossmember with diff drop kit fitted to the 100 Series Toyota Landcruiser (Front view)
A completed Superior crossmember with diff drop kit fitted to the 100 Series Toyota Landcruiser (Front view)

A completed Superior crossmember with diff drop kit fitted to the 100 Series Toyota Landcruiser (Rear view)
A completed Superior crossmember with diff drop kit fitted to the 100 Series Toyota Landcruiser (Rear view)

Summary

Just to recap, the Superior Engineering crossmember with diff drop is Australian made and manufactured from premium 350 grade steel, then CNC machined for the ultimate in durability and performance.

They are designed to suit the 100 Series Toyota Landcruiser four wheel drive vehicle.

This underbody component is sand blasted and black powder coated for maximum durability and the highest quality finish.

Even the Superior logo is pop riveted into the crossmember to ensure you’re getting a true quality GENUINE 4×4 accessory.

So, if you want to protect your vehicle CV joints and suspension geometry then you need a Superior Engineering structural crossmember with diff drop.

They are available to purchase online (24 hours a day – 7 days a week), over the phone during business hours or in-person at the Superior Engineering Deception Bay 4×4 Super Showroom.


Want More Information Click Here or Comment Below

Superior Diff Drop Kit Toyota Landcruiser 200 Series

This innovative diff drop kit has been custom designed and manufactured specifically for the 200 Series Toyota Landcruiser four wheel drive vehicle.

Superior Diff drop kits are designed to drop the front differential 25mm lower to fix the cv angle after a 2″ inch lift kit has been fitted and they also space down the original front guards.

The spacers are machine cut from high grade solid bar steel for a precise fit and zinc coated for hard wearing corrosion resistant protection.

Features a simple design for easy care and maintenance, utilises factory mounts and are fabricated by trained qualified professionals.

A full fitting kit is provided, which includes all the necessary high tensile bolts, spacers, hardware and instructions for a quick, easy, 100% bolt-in installation… requiring no cutting, welding or modification to the vehicle.

These diff drop kits are proudly manufactured by Superior Engineering right here in Australia so you know you’re getting quality.

They are manufactured to be Street Legal and Compliant within Australia so you don’t require separate approvals.

Diff Drop Features & Highlights:

  • 25mm Drop To Fix CV Anlges
  • Designed To Space Down Front Guard
  • Full Bolt-In Installation (No Modifications)
  • Corrossion Resistant Zinc Coat Finish
  • Precision Machined Cut Spacers
  • Made Right Here In Australia
  • Street Legal & Compliant
  • Utilises Factory Mounts
  • Heavy Duty Fabrication
  • Includes Hardware & Instructions


Buy Online

Diff Drop Kit Photo Gallery:

Superior Diff Drop Kit fitted to a Toyota Landcruiser 200 Series
Superior Diff Drop Kit fitted to a 200 Series
Closeup view of the Superior Diff Drop spacers fitted in the 200 Series
Closeup view of the Superior Diff Drop spacers fitted in the 200 Series
Superior Diff Drop spacers fitted to the 200 Series Landcruiser
Superior Diff Drop spacers fitted to the 200 Series Landcruiser
Right side view of a Toyota Landcruiser 200 Series after fitting the Superior Diff Drop kit
Left side view of a Toyota Landcruiser 200 Series after fitting the Superior Diff Drop kit
Complete Toyota Landcruiser 200 Series Superior Diff Drop kit with all the hardware


Request More Information

Superior 2 Inch Wheel Spacers

Superior 2 Inch Wheel spacers are used to move the tyre away from the chassis to help in articulation and to give a more stable ride due to the wider wheel track.

Being able to increase your wheel track will increase your stability while offroad creating less chance of vehicle rollovers.

For vehicles that run larger tyres or have excessive wheel travel, Superior wheel spacers will offer much needed clearance between the chassis and inner tyre.

All of our spacers are made from T6 6000 Aircraft grade billet alloy (Aluminium) and are precision CNC machined, then zinc coated to prevent corrosion.

Our wheel spacers are clearly marked and identified with the “Superior Engineering” logo machine engraved into the side of the spacer so you know you’re getting a “Genuine and Authentic” Superior spacer.

World First: Superior Engineering wheel spacers are the only spacers that come with custom drop shank wheel nuts to further engauge more thread than any other suppliers equivelant spacers.

Wheel Spacer Uses

  • Perfect for matching indifferent track widths… be it from the factory or from an axel swap.
  • Also can be used if chasing extra track width for competition or similar for side slope stability.
  • Can also help with fitment of different offset wheels to different vehicles.
Buy These Online

Wheel Spacer Gallery

Closeup of a single Superior 2 inch wheel spacer
Closeup of a single Superior 2 inch wheel spacer

Closeup of a 5 stud Superior 2 inch wheel spacer
Closeup of a 5 stud Superior 2 inch wheel spacer

Closeup of a stud and wheel nut on the Superior wheel spacer
Closeup of a stud and wheel nut on the Superior wheel spacer

Rear view of the Superior wheel spacer
Rear view of the Superior wheel spacer

A pair of premium Superior Engineering 5 stud wheel spacers
A pair of premium Superior Engineering 5 stud wheel spacers

Closeup of a pair of premium Superior Engineering 5 stud wheel spacers
Closeup of a pair of premium Superior Engineering 5 stud wheel spacers

Top view of a pair of premium Superior 5 stud 2 inch wheel spacers
Top view of a pair of premium Superior 5 stud 2 inch wheel spacers

Top closeup view of the Superior 5 stud 2 inch wheel spacers
Top closeup view of the Superior 5 stud 2 inch wheel spacers
Buy These Online